# PSU clicking/crackling noise ONLY during specific AI workloads (ComfyUI Moss Image), silent in FurMark at 575W — retained record

> Retained reddit record from reddit:StableDiffusion.

Canonical: https://highsignal.app/data/records/4f3cae9f7793012d

[← sources](https://highsignal.app/data)


source: [reddit](https://highsignal.app/data/reddit) (reddit:StableDiffusion)  published 2026-10-24 11:02 ingested 2026-10-25 02:38

[original source ↗](https://www.reddit.com/r/StableDiffusion/comments/1xe5se5/psu_clickingcrackling_noise_only_during_specific/)

## retained text



```
Note: This is not AI slop, the problem is very real. The format was generated by Claude because I used it to look into the problem. Also, English isn't my native language, so really, it's better written by Claude.

Hi everyone,

I'm getting a discontinuous electrical clicking/crackling noise coming directly from my PSU whenever my RTX 5090 hits 100% load in ComfyUI (video attached). Interestingly, this happens **specifically with ComfyUI's default Moss Image workflow**—it does not happen at all when running **Krea 2** or **Qwen Image** workflows. The noise stops the exact millisecond the generation finishes.

**Specs:**

* **CPU:** Ryzen 7 9800X3D
* **Motherboard:** ASUS Prime X870-P Wifi
* **GPU:** ASUS TUF RTX 5090 (connected directly with the native be quiet! 12VHPWR cable, no adapters)
* **PSU:** be quiet! Dark Power 13 1000W (ATX 3.0, 80 Plus Titanium)

**What I've tested so far:**

* **Cables & Voltages:** All cables are fully seated. In HWiNFO64, the 16-pin HVPWR voltage stays rock-solid above **12.3V** during the entire ComfyUI run.
* **GPU Fans:** Tested at 100% RPM in idle; the noise is 100% coming from inside the PSU, not the GPU fans.
* **FurMark & Other AI Models vs. Moss Image:** Running FurMark at a sustained **100% load / 575W (2836 MHz, 64°C GPU / 58°C VRAM)** produces **zero clicking noise**. Other AI workflows like **Krea 2** and **Qwen Image** are also completely silent. It only happens during the specific pulsating Tensor Core workload of the default **Moss Image** workflow (\~2.20 it/s).
* **Workarounds that stop the noise:** Setting "Prefer maximum performance" in the NVIDIA Control Panel didn't help. However, lowering the Power Limit to 85%, OR leaving the Power Limit at 100% and **flattening the voltage/frequency curve in MSI Afterburner at 900mV / 2700MHz** completely eliminates the clicking sound.

Since a flat 575W load in FurMark is dead silent, other AI models don't trigger it, and capping voltage spikes at 900mV fixes it at 100% PL, it seems the PSU's coils/components are reacting to a very specific frequency of rapid transient voltage spikes from GPU Boost between CUDA kernels in the Moss Image workflow.

Has anyone else experienced this specific clicking with the Dark Power 13 (1000W) and an RTX 5090/4090 under specific AI workflows or heavy transient loads? Would you consider this harmless magnetostriction/transient coil noise and just keep the 900mV undervolt, or is this a defective unit that I should RMA?

Thanks in advance!
```



document fetched 2026-10-25 00:30 · canonical https://reddit.com/r/StableDiffusion/comments/1xe5se5/psu_clickingcrackling_noise_only_during_specific
